A rear view mirror for a UTV serves a different purpose than one on a street vehicle
A UTV rear view mirror lets you see what is behind you without turning your head — useful when you are navigating tight trails, backing up to a trailer, or working in an open field. Unlike a car mirror, a UTV mirror must handle vibration, mud, water, and the angles of off-road terrain. The mirror you choose depends on your UTV's frame design, how you plan to use it, and whether you want a single mirror or dual mirrors.
Most UTVs come with either no mirror or a basic side mirror. Adding or upgrading a rear view mirror is one of the simpler exterior modifications you can do yourself, though some installations require drilling into the frame or roll cage.
Key Takeaways
- UTV rear view mirrors mount to the roll cage, windshield frame, or fender, and the mounting point determines which models will fit your machine.
- Glass mirrors are clearer but break easily on rough terrain; plastic or polycarbonate mirrors are more durable and lighter but may scratch or fog over time.
- Dual mirrors give you better visibility on both sides but add weight and can catch branches or obstacles on narrow trails.
- Installation usually takes 15 to 30 minutes with basic hand tools, but some mounts require drilling into the frame.
Where the mirror attaches on your UTV
The mounting location determines which mirror will work. Most UTV mirrors bolt to one of three places: the roll cage (the most common option on sport and utility models), the windshield frame (if your UTV has one), or the fender or A-pillar. Check your UTV's manual or look at the frame structure to see which mounting points are available and whether they are already drilled or require you to add holes.
Roll cage mounts are standard on most aftermarket mirrors because they are high enough to clear the hood and give a clear sightline. Windshield frame mounts work well if your UTV has a full windshield, but they limit your view if the windshield is small or partial. Fender mounts are less common and work best on side-by-side models with wider fenders.
Before you buy, measure the diameter of the tube or frame where you plan to mount the mirror. Most UTV roll cages use 1.75-inch or 2-inch diameter tubing. Mirrors come with clamps or brackets sized for specific tube diameters, so getting this wrong means the mirror will either not fit or will slip during use.
Glass versus plastic mirror heads
The mirror head — the reflective surface itself — comes in two main materials. Glass mirrors are clearer and do not scratch as easily as plastic, but they shatter on impact and add more weight to the mount. Plastic or polycarbonate mirrors are lighter, more durable in crashes, and less likely to injure you if you hit a branch, but they scratch more easily and can become cloudy or discolored after prolonged sun exposure.
For trail riding where you expect impacts, plastic is the safer choice. For slower work like backing up to a trailer or moving through open fields, glass gives you a clearer image. Some mirrors use a hybrid approach: a plastic-backed mirror with a glass reflective surface, which balances durability and clarity.
Check whether the mirror head is adjustable. A ball joint or swivel mount lets you angle the mirror to your line of sight without removing it. Fixed mounts are simpler and lighter but harder to aim correctly, especially if you are tall or short relative to the UTV's design.
Single mirror versus dual mirrors
A single rear view mirror (usually mounted center-top on the roll cage) gives you one sightline behind you but leaves blind spots on the sides. Dual mirrors (one on each side) eliminate most blind spots and let you see traffic or obstacles on both flanks. The trade-off is weight, cost, and the risk of catching a mirror on a branch or obstacle on narrow trails.
For trail riding in tight spaces, many riders prefer a single center mirror to reduce snag points. For open-field work, towing, or riding on wider trails, dual mirrors are worth the extra cost and weight. Some riders run a single rear view mirror plus existing side mirrors for a three-mirror setup.
Installation steps and tools you will need
Most UTV rear view mirrors bolt on with basic hand tools. You will need an adjustable wrench or socket set (usually 8mm to 12mm sizes), a drill with a metal bit if your mounting point is not pre-drilled, and possibly a rubber mallet to seat the clamp. Some mirrors come with rubber shims or spacers to prevent the clamp from slipping on smooth tubing.
The basic process: loosen the clamp on the mirror bracket, position it on the roll cage or frame at your chosen height and angle, tighten the clamp bolts in a cross pattern (like tightening a wheel), and then adjust the mirror head to your sightline. If you are drilling new holes, mark the spot with a center punch first to keep the bit from wandering. Use a metal bit and go slowly to avoid cracking the tubing.
Test the mirror by shaking the UTV or the roll cage by hand. A properly installed mirror should not move or rattle. If it does, tighten the bolts further or add a rubber shim under the clamp. Check the tightness again after your first ride, as vibration can loosen bolts over time.
Common mirror styles and what they cost
Basic roll cage mirrors with plastic heads and fixed mounts run from $25 to $60 per mirror. Mid-range mirrors with adjustable ball joints, better-quality plastic or hybrid glass-plastic heads, and stainless steel brackets cost $60 to $120. Premium mirrors with full glass heads, heavy-duty aluminum or stainless brackets, and quick-adjust mounts can exceed $150 each.
Dual mirror kits (two mirrors plus brackets) are usually cheaper per mirror than buying them individually. A complete dual setup with plastic heads and standard mounts might cost $80 to $150, while a premium dual kit with glass and adjustable mounts can run $250 to $400.
Aftermarket brands like Seizmik, SuperATV, and Polaris (if you own a Polaris UTV) offer mirrors designed specifically for UTV mounting. Generic motorcycle or ATV mirrors sometimes fit, but they may not be angled correctly for a UTV's seating position or may not clamp securely to larger-diameter roll cage tubing.
Maintenance and when to replace
Clean your mirror regularly with a soft cloth and mild soap to remove mud and dust. Avoid harsh solvents or abrasive scrubbing, which can scratch plastic mirrors. If the mirror head becomes cloudy or the reflective surface peels, replacement heads are often sold separately and cost $15 to $50, so you do not have to replace the entire bracket.
Check the clamp bolts every few months, especially after rough rides. Vibration can loosen them gradually. If the mirror develops a rattle or wobbles, tighten the bolts and consider adding a rubber shim or thread-locking compound to keep them from loosening again.
If you crash or hit a branch hard enough to bend the bracket, the mirror may not return to the correct angle. Some brackets are designed to fold or swing back on impact and then reset, while others bend permanently. Check the product description to see whether your mirror is impact-resistant or fixed.
Frequently Asked Questions
Will a motorcycle or ATV mirror fit my UTV?
Sometimes, but not always. Motorcycle mirrors usually have smaller clamps designed for 7/8-inch or 1-inch tubing, while most UTVs use 1.75-inch or 2-inch roll cage tubes. An ATV mirror might fit if your UTV has a smaller frame, but the mounting angle and sightline may not be right for a UTV's higher seating position. Measure your tubing diameter before trying to adapt a non-UTV mirror.
Can I install a rear view mirror without drilling?
Yes, if your UTV's roll cage or frame already has mounting holes or if you choose a clamp-on bracket that does not require drilling. Most aftermarket clamp-on mirrors are designed to fit without drilling. If your mounting point is smooth tubing with no holes, you will need to drill unless you use a clamp-style bracket that tightens around the tube.
Do I need a rear view mirror if my UTV has side mirrors?
Side mirrors show what is beside you, but a rear view mirror shows what is directly behind you. They serve different purposes. A rear view mirror is most useful when backing up, towing, or working in open areas where you need to see traffic or obstacles behind you. On narrow trails, a single rear view mirror may be enough.
What is the best angle for a rear view mirror?
Adjust the mirror so you can see directly behind the UTV without turning your head or moving your eyes far to the side. Sit in the driver's seat, look straight ahead, and angle the mirror so the center of the reflective surface shows the area 10 to 20 feet behind you. If the mirror has an adjustable ball joint, you can fine-tune this angle without tools.
Will a rear view mirror add much weight to my UTV?
No. A single mirror with bracket typically weighs 1 to 3 pounds, and dual mirrors weigh 2 to 6 pounds total. This is negligible on most UTVs, which weigh 1,000 to 2,000 pounds. The weight difference between a plastic mirror and a glass mirror is usually less than half a pound per mirror.