What wheel sizes come on a Dodge Charger
Dodge Charger wheels range from 17 inches to 20 inches in diameter, depending on the model year and trim level. A base Charger typically rolls on 17-inch wheels, while higher trims and performance models use 18, 19, or 20-inch wheels. The width varies from about 7 inches to 9.5 inches, and the bolt pattern is 5x115mm across all modern Chargers — meaning any aftermarket wheel designed for a Charger will fit the lug holes, but the size and offset matter for clearance and handling.
The tire size printed on your door jamb or owner's manual is the real specification to follow when replacing wheels or tires. A common size on mid-trim Chargers is 225/60R18, while performance models might wear 245/45R20. Swapping to a larger wheel diameter usually means a shorter sidewall on the tire to keep the overall diameter close to stock — this affects ride quality, speedometer accuracy, and how the wheel sits in the wheel well.
Key Takeaways
- Dodge Charger wheels come in 17, 18, 19, or 20-inch diameters depending on the year and trim, with a 5x115mm bolt pattern on all modern models.
- The tire size on your door jamb is the specification you must match when replacing wheels, not just the wheel diameter alone.
- Upgrading to a larger wheel diameter requires a shorter tire sidewall to avoid speedometer error and suspension interference.
- Offset and backspacing determine how far the wheel sits from the hub — wrong offset can cause rubbing or poor handling even if the bolt pattern matches.
Wheel sizes by Charger generation
The sixth-generation Charger (2015–2023) came standard with 17-inch wheels on base and SXT trims, 18-inch wheels on GT and R/T models, and 20-inch wheels on R/T Scat Pack and Hellcat variants. The 2024 redesign maintains similar sizing: 18 inches on most trims and 20 inches on performance models. If you own a fifth-generation Charger (2011–2014), the standard was 18 inches, with 20-inch options on R/T and SRT models.
Older Chargers from the fourth generation (2006–2010) started at 17 inches and went up to 20 inches on SRT8 models. The bolt pattern changed in 2011 — earlier Chargers used 5x114.3mm, while 2011 and newer use 5x115mm. This means a wheel from a 2010 Charger will not bolt onto a 2011 Charger without an adapter, even though the difference is less than 1mm. Always verify the bolt pattern on your specific year before buying used wheels.
Offset and backspacing explained
Offset is the distance in millimeters from the wheel's centerline to the mounting surface where it bolts to the hub. A wheel with +45mm offset sits further toward the outside of the car than one with +35mm offset. Backspacing is the distance from the mounting surface to the inner edge of the wheel — it determines how close the wheel comes to the suspension and brake components.
A Charger with factory 18-inch wheels typically has an offset between +40mm and +50mm. If you install a wheel with too little offset (say, +25mm), the wheel will stick out past the fender and may rub the suspension at full turn or over bumps. Too much offset (say, +60mm) pulls the wheel inward and can cause the tire to rub the inside of the fender or interfere with the brake caliper. Manufacturers publish the correct offset range for each Charger year — check your owner's manual or the door jamb label before ordering wheels.
Tire size and overall diameter
The tire size is written as three numbers: width, aspect ratio, and diameter. A 225/60R18 tire is 225 millimeters wide, has a sidewall height that is 60 percent of the width (135mm), and fits a 18-inch wheel. The overall diameter of this tire is about 27.4 inches. If you switch to a 20-inch wheel with a 245/45R20 tire, the overall diameter is about 27.9 inches — close enough that your speedometer stays accurate.
Swapping to a much larger wheel without adjusting the tire sidewall throws off the overall diameter. A 225/60R18 to a 225/60R20 changes the overall diameter from 27.4 inches to 28.9 inches, which makes your speedometer read 5 percent slower than you are actually going and can trigger check-engine lights on some models. Tire shops and wheel retailers can calculate the correct tire size for your new wheel diameter to keep the overall diameter within 3 percent of stock.
Aftermarket wheel fitment and clearance
Aftermarket wheels must match three things: bolt pattern (5x115mm for 2011+ Chargers), center bore diameter, and offset. The center bore is the hole in the middle of the wheel that slides over the hub — Charger hubs are typically 71.5mm. A wheel with a smaller center bore will not fit; one with a larger center bore will fit but may vibrate because it is not centered on the hub.
Even with the correct bolt pattern and center bore, wrong offset causes problems. A wheel that is too far outboard (low offset) can rub the inside of the fender at full steering angle or over bumps, especially on lowered cars. A wheel that is too far inboard (high offset) can hit the brake caliper or suspension components. Measure your current wheel's offset and backspacing, or look it up in your owner's manual, before ordering replacements. Many wheel shops offer a fitment check if you provide your Charger's year, trim, and suspension height.
Upgrading from stock wheels
Moving from 18-inch to 20-inch wheels on a Charger is common and usually fits without modification. The offset range for 20-inch wheels on a Charger is typically +35mm to +50mm — slightly lower than 18-inch wheels because the larger diameter sits further from the hub. A +40mm offset 20-inch wheel is a safe choice for most Chargers with stock suspension.
Lowered Chargers need more caution. Dropping the car 1 to 1.5 inches reduces clearance between the tire and fender, so a wheel with lower offset (more outboard) can cause rubbing. Many owners of lowered Chargers go with a +30mm to +35mm offset on 20-inch wheels to push the tire outward and maintain clearance. Test fit the wheel on the car before paying for a full set, or ask the wheel shop to simulate the fitment using your Charger's specifications.
Reading your door jamb label
The driver's door jamb contains a label with the original tire size and sometimes the wheel size. This label is the factory specification for your exact Charger. It lists the tire size (for example, 225/60R18) and may include the wheel diameter and width. If you are replacing wheels, match the tire size on this label or consult a tire shop to find the correct tire size for your new wheel diameter.
The label does not always list the wheel offset or center bore — you may need to look up your specific year and trim in a Charger forum or contact a Dodge dealer parts department. Some aftermarket wheel retailers have fitment databases where you enter your Charger's year and trim, and the system shows wheels that fit without modification. This is faster than calculating offset yourself.
Frequently Asked Questions
Can I put 20-inch wheels on a Charger that came with 18-inch wheels?
Yes, as long as the offset is correct for your Charger's year and suspension height. A +40mm offset 20-inch wheel usually fits a stock Charger without rubbing. Lowered cars need lower offset (more outboard) to maintain clearance. Check with a wheel retailer or Charger forum for your specific year before ordering.
What is the bolt pattern for a 2015 Charger?
The 2015 Charger uses a 5x115mm bolt pattern. This is the same for all Chargers from 2011 onward. Older Chargers (2010 and earlier) use 5x114.3mm, so wheels are not interchangeable between these generations without an adapter.
Do I need to replace my tires if I get new wheels?
Not necessarily. If your current tires are in good condition and the correct size for your new wheels, you can move them over. If you are upgrading to a larger wheel diameter, you will need new tires in the correct size for that diameter — a tire shop can calculate the right size to keep your speedometer accurate.
What happens if my wheel offset is wrong?
Wrong offset causes the wheel to sit too far inboard or outboard. Too far outboard and the tire rubs the fender at full turn or over bumps. Too far inboard and the tire or wheel can hit the brake caliper or suspension parts. Either way, you risk damage and poor handling. Always verify offset before installing wheels.
Where can I find the correct wheel offset for my Charger?
Check your owner's manual, the door jamb label, or contact a Dodge dealer parts department with your year and trim. Aftermarket wheel retailers often have fitment databases for Chargers. Charger forums and enthusiast communities also maintain offset and backspacing charts for each generation.